Why won t my Hoover spin?

Lift the brush roll up and out and remove the broken or worn belt . Clean any debris tangled around the brush and if the bristles look worn then fit a new replacement brush. loop one end of the belt over the metal drive pulley within the body of the cleaner and loop the other end over the brush roll.

How does a Hoover Power Scrub carpet cleaner work?

Things You Should Know Depending on the model, pour the cleaner into the water tank or solution compartment. Squeeze the trigger on your cleaner to release the cleaning solution. Move the machine forward and back to suck up the dirty water. Go over the entire area with a rinse cycle once you've cleaned the carpet.

What setting do you vacuum carpet on?

For bare floors, use the lowest or bare floor setting, for short and medium pile carpets use a medium setting and finally, for plush carpets use the highest setting . When vacuuming, there should be minimal resistance, if it is difficult to push, adjust to the next highest setting.

How do I get my carpet cleaner to work?

Plug the power cord into a nearby outlet, then locate the buttons on the cleaner's back. Press both buttons down to turn the machine on and activate its heating system. Pull the handle's trigger while moving the cleaner forward and back. Pull the trigger to spray water onto the carpet.

Why is my Hoover not picking up water?

Empty the dirty water tank :A full tank can prevent the cleaner from sucking up more water.To empty the tank, press down on the handle or latch at the top. Rinse the tank in the sink before replacing it. Check the gasket:A broken or poorly sealed gasket can prevent good suction.

Why is my carpet shampooer not picking up water?

If your carpet cleaner is not spraying or picking up water, there are a few things to check. Ensure the filter is clean and dry before placing it back in the machine . If water leaks, remove the tanks and fill them with hot tap water. Hold them over the sink with the cap down and inspect for any leaks in the tank.

Where does the water go in a Hoover carpet cleaner?

A: There are two clear tanks on the top of the carpet cleaner . One is for water which is the largest reservoir and the smaller one is for the solution.

How much water does the Hoover Power Scrub hold?

A: The tank holds a gallon of water and there is a solution tank you fill up to the max fill line it will mix the solution automatically I would use a concentrate and no need to dilute it.

How do you spin only on a Hoover washing machine?

All Hoover laundry products have a 'spin only' cycle. This will give a full speed spin and last up to 10 minutes. Look for the swirling circle symbol on the dial - your instruction book will give further information. The full spin may not be suitable for delicate fabrics, wools and silks.

How do you use a Hoover robot?

To use a robot vacuum cleaner, charge it fully and connect it to your app, let the device map the space and you can start cleaning or set cleaning schedules via the app right away .

Hoover SpinScrub User Manual (2024)

™

SpinScrub with MAX Extract

The Easy to Use Deep Cleaner

Congratulations on your purchase

™ ™

SteamVac SpinScrub cleaners have 6 rotating brushes that deep clean carpets and scrub bare floors!

SteamVac™ SpinScrub™ Deep Cleaner cleans carpet fibers by applying hot tap water and cleaning solution.

www.hoover.com

Fill in and Retain

This HOOVER deep cleaner is designed for deep cleaning carpet, rugs, carpeted stairs and upholstery. The model and serial numbers are located on the data label on the back of the handle.

For your personal records, please enter the COMPLETE model and serial numbers in the spaces provided and retain this information.

Your deep cleaner is model

and has serial number

It is suggested that you attach your sales receipt to this owner s manual.

Verification of date of purchase may be required for warranty service of your Hoover product.

Index

Important safeguards . . . . . . . . . . 2

Assembly . . . . . . . . . . . . . . . . . . . 4-5

Carton contents. . . . . . . . . . . . . . 3

How to use. . . . . . . . . . . . . . . . . . 6-9

Agitator speed selector . . . . . . . 7

Automatic “shut-off” . . . . . . . . . . 7

Deep cleaner description . . . . . . 6

Emptying the recovery tank . . 8-9 Filling the clean solution tank . 7-8

How to clean

After cleaning . . . . . . . . . . . . 9-10

Before you begin . . . . . . . . . . . . 9

Carpet cleaning . . . . . . . . . . . . . 10

Cleaning bare floors . . . . . . . . . 11

Clean Surge Feature . . . . . . . . 10

MAX Extract Feature . . . . . . . . . 7

Picking up spills . . . . . . . . . . . . 10

Using the tools . . . . . . . . . . 11-13

Attaching tools . . . . . . . . . . . . 11

Cleaning carpeted stairs. . . . . 12

Cleaning upholstery . . . . . . . 13

Scrub module . . . . . . . . . . . . 11-12

Maintenance

Headlight replacement . . . . . 13-14

If you have a problem . . . . . . . . 15

Lubrication . . . . . . . . . . . . . . . . 14

Service . . . . . . . . . . . . . . . . . . . 15

Storage . . . . . . . . . . . . . . . . . . . 14

Warranty . . . . . . . . . . . . . . . . . . . . 15

w w w. h o ov e r. c o m

™

Owner’s Manual

ENGLISH ➜ pp. 1-15 ESPAÑOL ➜ pág. 17-26 FRANÇAIS ➜ p. 27-35

Review this manual before operating deep cleaner

I m p o rtant Safeguard s !

When using an electrical appliance, always follow basic

precaution, including the following:

READ ALL INSTRUCTIONS BEFORE USING APPLI-

To reduce the risk of fire, electric

WARNING:

• Use indoors only.

• Use only on surfaces moistened by the cleaning process or small spills. Do not immerse product.

• Connect to a properly grounded outlet only. See “Grounding Instructions”.

• Do not clean over floor electrical outlets.

• Do not use without tanks in place.

• Use extra care when cleaning on stairs. Do not place deep cleaner on stairs.

• Use deep cleaner only for its intended use as described in the instructions.

• Use only attachments recommended by The Hoover Company; others may cause hazards.

• The use of an extension cord is not recommended. If an extension cord is absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-prong grounding type plug and a 3-pole receptacle that accepts the machine plug.

• Unplug deep cleaner when not in use.Turn off all controls before unplugging.

• Unplug before connecting the powered hand tool.

• A lw ays disconnect cord from electrical outlet before servicing the deep cl e a n e r.

• Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.

• Never handle plug or appliance with wet hands.

• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer.

• Close supervision is necessary when any appliance is used by or near children. Do not allow deep cleaner to be used as a toy or to run unattended at any time.

• Do not point tools toward people or pets.

• Use only commercially available floor cleaners intended for machine application. Do not use any type of wax with deep cleaner.

• To assist In reducing drying time, be certain the area is well ventilated when using detergents and other cleaners with this machine.

• Keep detergents and other cleaners out of children's reach.

• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

• Do not pick up chlorine bleach,drain cleaner, gasoline or any other toxic material with this appliance.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Avoid picking up hard, sharp objects with the deep cleaner.They may damage the machine.

• Keep hair, loose clothing, fingers, feet and all parts of body away from openings and moving parts.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

• To help prevent matting and resoiling, avoid contact with carpets until they are dry.Keep children and pets away from carpets until they are completely dry.

• Store in a dry place. Do not expose machine to freezing temperatures.

Save these instru c t i o n s !

shock, or injury:

Grounding Instructions

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor (C) and grounding plug (A). The plug must be plugged into an appropriate outlet (B) that is properly installed and grounded in accordance with all local codes and ordinances.

1. Assembly

DANGER-

Improper connection of the equipmentgrounding conductor can result in the risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in sketch (A).

A temporary adapter (D) may be used to connect this plug to a 2-pole receptacle (E) if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (B) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like (F) extending from the adapter must be connected to a permanent ground (G) such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.

Carton contents

1-1

Unpack deep cleaner from the carton and identify the parts shown. Remove and dispose of the packing.

A. Deep cleaner B. Upper handle with powered hand tool and

scrub module C. Bolts (2) D. Nuts (3 - one extra included) E. Carpet/Upholstery Detergent F. Bare Floor Cleaner G. Bare floor attachment

H. Hose holder I. Crevice tool J. Nozzle cleanout-tool Contained in carton with hose: K. Hose L. Stair/upholstery nozzle M. Tool holder and screw (taped on rack under nozzle)

Continued ➜

The assembled cleaner will look like this drawing.

Assemble handle

1-2

Attach upper handle

Remove clean solution tank (upper tank) from deep cleaner.

1-3

With hose hook (A1) and cord hook (A2) to back of deep cleaner, push upper handle down onto lower handle. Push b o l t s i n t o holes on f ront of handle. If bolts will not

go through hole easily handle is not pushed completely dow n .

1-4

Attach hose holder

Position hose holder (B) onto handle by matching tabs on rack with openings on back of handle. Make sure holes for bolts are aligned.

1-7

1-5

Place nuts in recessed areas on back of handle. Hold each nut in place while

tightening each bolt securely (from the front of the handle) with a Phillips screw driver.

Only two nuts are needed on this model.

The extra nut is not required but has been provided for your convenience.

1 - 8

1-6

When handle sections are completely together, squeeze trigger (C) and depress Clean Surge™ Button (D) on upper handle.

You will hear a “snap”when the trigger rod is in place.

1 - 9

Replace clean solution tank (upper tank) by positioning bottom first. Press on tank handle to snap top of tank into place.

Attach tool holder

Remove tool and taped screw from holder.

Insert projections on holder into slots on back of cleaner.

Slide rack down into place. Insert screw at (E) and tighten with a Phillips screwdriver.

1-10

1 - 1 1

1 - 1 2

Press cord into cord clip on back of handle. Pull cord tight and wrap cord around hooks (A2).

1 - 1 3

Slide crevice tool (I) into holder. Position stair/upholstery nozzle in holder

at base of cleaner and snap it into place as shown at arrow.

1 - 1 6

Storing hose & tools

Store hose on rack by first positioning hose in front section of clip.

1 - 1 4

Insert end of bare floor attachment into holder and snap into clip as shown.

1 - 1 7

Continue wrapping hose over upper hose hook (F) and under lower hook (G). Snap hose end fully into holder (H).

Ensure that the hose end is pushed down completely into holder (H).

1 - 1 5

Powered hand tool

The powered hand tool is shipped in a plastic bag for protection. Remove the bag before using the tool by first opening tool door.

To remove powered hand tool (J), pull it down and outward. To reposition the tool, reverse this procedure.

To remove the scrub module (K), grasp it at the sides and pull it forward. To reposition module, fit tabs in the storage area into holes on back of module. Push module to snap it securely into position.

How to reattach tool cover

The tool cover is designed with a breakaway feature which allows it to snap free if it is pushed open too far.

To reattach, align hinges of cover with holes on sides of tool storage area.

Hoover SpinScrub User Manual (2024)

FAQs

Why won t my Hoover spin? ›

References